4x4 XLR Dante® Audio Bridge, Mic/Line Inputs with +48V, 8-Band PEQ, Delay, Redundant PoE+, 1U Rack

Level-Match, EQ and Time-Align at the Bridge - 8-Band PEQ on Every Input and Output, up to 50ms Output Delay, 6 Input Sensitivities

AUD-DTE-4X4XLRUPC 813982024403
4x4 XLR Dante® Audio Bridge with 8-Band PEQ and Delay, 1U Rack – KanexPro AUD-DTE-4X4XLR
Available through our B2B portal
This part is sold to approved trade accounts.

Resellers, installers, schools and businesses. Approval is usually the same working day.

Overview

Brings four analog sources onto a Dante® network and sends four Dante® feeds back out to analog, with level matching, EQ and time alignment handled in the bridge itself. AUD-DTE-4X4XLR is a 1U, 19-inch metal rack unit. It has four XLR/TRS combo mic/line inputs, each with switchable +48V phantom power, and four balanced XLR line outputs.

A global line-up setting chooses one of six input sensitivities, from -35dBV for microphones to +24dBu for hot console outputs, and one of five output levels, from +20dBu to -18dBV. The same unit can take condenser mics and wireless receivers and drive professional or consumer-level destinations. Every input and output has an 8-band parametric EQ (+/-15dB) with parametric, shelf and pass filters, and every output has up to 50ms of delay. Five presets store complete room setups. The unit is configured from its built-in Web GUI or from Dante® Controller, supports AES67, and accepts ASCII commands over TCP/IP and Telnet from a control system. It has primary and secondary Dante® ports, and both can take PoE+. If the primary network fails, audio switches to the secondary network automatically, and either port can power the unit on its own.

Key features
  • Four balanced analog inputs on XLR/TRS combo connectors, female
  • Four balanced analog outputs on XLR, male
  • Dante® 4x4 and AES67 audio input and output
  • Primary and secondary Dante® ports on locking RJ45 connectors, both PoE+ (Class 4, IEEE 802.3at); audio switches to the secondary network automatically if the primary fails, and either port can power the unit on its own
  • Gigabit (1000M) Dante® network connection over CAT6/6A/7, up to 328ft (100m) to the switch
  • Accepts and delivers balanced or unbalanced analog audio
  • +48V phantom power on each input, switched on or off per input, with a rear-panel indicator for each input
  • Adjustable global 0dBFS line-up selection:
    • Six input sensitivity levels: -35dBV, -18dBV, 0dBV, +4dBu, +14dBu, +24dBu
    • Five output levels: +20dBu, +14dBu, +4dBu, 0dBV, -18dBV
  • Built-in audio DSP for sensitivity gain, 8-band PEQ and delay control
  • 8-band PEQ (+/-15dB) on every input and output, with Parametric, Lowpass, Highpass, Low Shelf and High Shelf filter types; stereo linking of input and output pairs; copy, import and export of PEQ settings
  • Up to 50ms of delay on every output
  • Dante® audio at 44.1kHz, 48kHz, 88.2kHz and 96kHz sampling rates, 16- or 24-bit
  • Five preset scenes for saving and recalling complete setups
  • Set up from the built-in Web GUI, with separate Admin and User accounts, or from Dante® Controller
  • ASCII API control over TCP/IP (default port 8000) and Telnet (default port 23)
  • DHCP or static IP addressing, set separately for the primary and secondary networks
  • Firmware updates and configuration export and import from the Web GUI
  • 12V DC locking power input (max 2.5A) and GND terminal
  • Standard 1U 19-inch rack-mount metal chassis
  • Works with RelayAV, KanexPro's control app: master volume and mute, each output's volume, mute, delay and level, each input's gain, mute, sensitivity and 48 V phantom power, input and output EQ, presets, auto standby and power, from the RelayAV app
Audio
Dante® AudioDante®/AES67 digital audio in/out; 44.1kHz, 48kHz, 88.2kHz, 96kHz; 16/24-bit
Analog Inputs4x mic/line, balanced/unbalanced
Analog Outputs4x line, balanced/unbalanced
Input Sensitivity-35dBV, -18dBV, 0dBV, +4dBu, +14dBu, +24dBu
Output Level+20dBu, +14dBu, +4dBu, 0dBV, -18dBV
Input LevelMax 24dBu (12.28Vrms), balanced line audio
Max 18dBu (6.14Vrms), unbalanced line audio
Min -35dBV (17.78mVrms), balanced mic audio
Input Impedance20k Ohm balanced
10k Ohm unbalanced
Output Level (Max)20dBu (7.75Vrms), balanced audio
14dBu (3.875Vrms), unbalanced audio
Output Impedance600 Ohm balanced
300 Ohm unbalanced
Phantom Power+48V on each input, switchable per input
THD+N< 0.01% at +4dBu, 1kHz
S/N Ratioat least 105dB at +4dBu, 1kHz, A-weighted
Dynamic Rangeat least 105dB at +4dBu, 1kHz, A-weighted
Frequency Response20Hz to 20kHz (+/-0.5dB)
DSP
Parametric EQ8 bands on every input and output; +/-15dB gain; 20Hz to 20kHz; Q 0.02 to 16
Filter TypesParametric, Lowpass, Highpass, Low Shelf, High Shelf
Input Gain-12dB to +12dB, 0.1dB steps
Output Delay0 to 50ms per output
Presets5 user presets
Connections
Mic/Line Inputs4x XLR/TRS combo, female
Line Outputs4x XLR, male
Dante® Primary1x RJ45 locking connector, PoE+/PD (Class 4, IEEE 802.3at)
Dante® Secondary1x RJ45 locking connector, PoE+/PD (Class 4, IEEE 802.3at)
Power1x 12V DC, 2-pin locking jack, max 2.5A
Ground1x GND terminal
XLR PinoutPin 1: Ground/Shield; Pin 2: Positive/Hot; Pin 3: Negative/Cold
Network and Control
Network BandwidthDante® network, 1000M
Transmission Distance328 ft (100 m) over CAT6/6A/7
ControlBuilt-in Web GUI, Dante® Controller, TCP/IP and Telnet ASCII API; RelayAV
Default PortsTCP/IP: 8000; Telnet: 23 (both configurable)
IP AddressingDHCP (default) or static, set per network
Indicators and Buttons
Front PanelPOWER LED, STATUS LED, RESET button
Rear Panel4x green 48V phantom power indicators, one per input
Power
Power Supply12V/2.5A 2-pin locking power supply, or PoE+/PD (Class 4, IEEE 802.3at)
Power Consumption10.2W max
Physical
HousingMetal enclosure
ColorBlack
Form FactorStandard 1U 19-inch rack-mount
Dimensions (W x D x H)17.32 x 7.87 x 1.73 in (440 x 200 x 44 mm)
Weight4.72 lbs (2.14 kg)
Environmental
Operating Temperature32°F to 104°F (0°C to 40°C)
Storage Temperature-4°F to 140°F (-20°C to 60°C)
Operating Humidity20% to 80% RH, non-condensing
Storage Humidity10% to 90% RH, non-condensing
ESD ProtectionIEC 61000-4-2: +/-8kV (air-gap discharge), +/-4kV (contact discharge)
Package Contents
1xAUD-DTE-4X4XLR 4x4 XLR Dante® Audio Bridge
1x12V/2.5A locking power supply with multinational plug adapters
2xRack-mounting ears
8xMachine screws
4x4 XLR Dante® Audio Bridge, Mic/Line Inputs with +48V, 8-Band PEQ, Delay, Redundant PoE+, 1U Rack panel drawing
4x4 XLR Dante® Audio Bridge, Mic/Line Inputs with +48V, 8-Band PEQ, Delay, Redundant PoE+, 1U Rack system diagram
4x4 XLR Dante® Audio Bridge, Mic/Line Inputs with +48V, 8-Band PEQ, Delay, Redundant PoE+, 1U Rack applications
in the same range
AUD-DTE-4X4LINE 4x4 Mic/Line Dante® and AES67 Bridge with 8-Band PEQ and Delay
Tune and Time-Align at the Interface - 8-Band PEQ on All 8 I/O, Up to...
B2B portal only
in the same range
AUD-DTE-2X2XLR 2x2 XLR Dante Audio Bridge with DSP, 8-Band PEQ and Delay
Mic-to-Line Analog onto Dante® and Back, Tuned at the Box, from -35dB...
B2B portal only
in the same range
AUD-DTE-8X8XLR 8x8 XLR to Dante/AES67 Audio Bridge with +48V Phantom, PEQ an...
Mic and Line Sources onto a Dante® Network Without a Separate Preamp ...
B2B portal only
in the same range
AUD-DTE-16X16XLR 16x16 XLR Audio Bridge with Dante® and PoE+, 19" Rack Mount
One Chassis Replaces Separate Input and Output Units - 16 XLR/TRS Com...
B2B portal only
in the same range
AUD-DTE-8X8LINE Dante 8x8 Analog Audio Bridge with DSP, Phoenix I/O, PoE+
Replace a Bank of 2-Channel Dante® Adapters with One Unit - 8 Mic/Lin...
B2B portal only

Buying for resale, a project, or your own site?

Trade accounts see net pricing, stock and one-click reorder from past jobs. Dealers, integrators, businesses, schools and public bodies all qualify. Approval is usually the same working day.