Dante 8x8 Analog Audio Bridge with DSP, Phoenix I/O, PoE+

Replace a Bank of 2-Channel Dante® Adapters with One Unit - 8 Mic/Line In, 8 Line Out, One Switch Port

AUD-DTE-8X8LINEUPC 813982024298
Dante 8x8 Analog Audio Bridge with DSP, Phoenix I/O, PoE+ – KanexPro AUD-DTE-8X8LINE
Available through our B2B portal
This part is sold to approved trade accounts.

Resellers, installers, schools and businesses. Approval is usually the same working day.

Overview

Puts eight analog mics or line sources onto a Dante® network and brings eight Dante® channels back out to analog amplifiers and speakers, all from one rack-mount unit on one switch port. The AUD-DTE-8X8LINE is a 19-inch rack-mount bridge in a black metal enclosure. It has eight balanced or unbalanced mic/line inputs, each with switchable +48V phantom power, and eight balanced or unbalanced line outputs. All I/O terminates on 12-pin 3.5mm Phoenix connectors.

The primary and secondary Dante® ports run as hot backups, so audio moves to the secondary network automatically if the primary fails. Onboard DSP gives every input and output its own gain and 8-band parametric EQ (+/-15 dB) and every output up to 50 ms of delay. A selectable 0 dBFS line-up from -35 dBV to +24 dBu matches mic-level, consumer-level and pro-level gear. Setup runs from the built-in Web GUI, which stores five preset scenes, and control systems can use TCP/IP and Telnet commands. The strongest advantage is consolidation: one managed Dante® device with one PoE+ load replaces a bank of 2-channel endpoints, so there are fewer devices to mount, power, label and patch.

Key features
  • 8x mic/line balanced or unbalanced audio inputs
  • 8x balanced or unbalanced audio outputs
  • Dante® 8x8 and AES67 audio input and output
  • +48V phantom power on each input, with a phantom power indicator for each input on the rear panel
  • Adjustable 0 dBFS line-up selection: -35 dBV, -18 dBV, 0 dBV, +4 dBu, +14 dBu or +24 dBu
  • Five selectable output levels: +20 dBu, +14 dBu, +4 dBu, 0 dBV or -18 dBV
  • Built-in audio DSP for sensitivity, gain, 8-band PEQ and delay
  • 8-band PEQ on every audio input and output (+/-15 dB gain) with Parametric, Lowpass, Highpass, Low Shelf and High Shelf filter types, plus up to 50 ms of output delay
  • Dante® audio at 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz sampling rates, 16 or 24 bit
  • Configuration from the internal Web GUI or from Dante® Controller
  • TCP/IP and Telnet ASCII command control for third-party control systems
  • 12-pin 3.5mm Phoenix connectors on all analog inputs and outputs
  • Standard 19-inch rack-mount form factor, with mounting ears included
  • Works with RelayAV, KanexPro's control app: each output's gain, mute, delay and level, each input's gain, mute, sensitivity, delay and 48 V phantom power, DCA groups, input and output EQ, expander, limiter, presets, auto standby and power, from the RelayAV app
Audio
Analog Inputs8x mic/line, balanced or unbalanced
Analog Outputs8x line, balanced or unbalanced
Dante® Channels8 in / 8 out
Dante® Audio FormatDante®/AES67 digital audio in/out, PCM, 44.1 kHz to 96 kHz, 16/24-bit
Line Input LevelMax +24 dBu (12.28 Vrms), balanced
Max +18 dBu (6.14 Vrms), unbalanced
Mic Input LevelMin -35 dBV (17.78 mVrms), balanced
Input Sensitivity+24 dBu, +14 dBu, +4 dBu, 0 dBV, -18 dBV, -35 dBV (selectable per input)
Input Impedance20 k Ohm balanced
10 k Ohm unbalanced
Phantom Power+48V, switchable per input
Line Output LevelMax +20 dBu (7.75 Vrms), balanced
Max +14 dBu (3.875 Vrms), unbalanced
Min -18 dBV
Output Level Selection+20 dBu, +14 dBu, +4 dBu, 0 dBV, -18 dBV (selectable per output)
Output Impedance600 Ohm balanced
300 Ohm unbalanced
Performance
THD+N< 0.01% at +4 dBu, 1 kHz
S/N Ratioat least 105 dB at +4 dBu, 1 kHz, A-weighted
Dynamic Rangeat least 105 dB at +4 dBu, 1 kHz, A-weighted
Frequency Response20 Hz to 20 kHz (+/-0.5 dB)
DSP
Input Gain-12 dB to +12 dB, 0.1 dB steps
Parametric EQ8 bands on every input and output; gain -15 dB to +15 dB; frequency 20 Hz to 20 kHz; Q 0.02 to 16
Filter TypesParametric, Lowpass, Highpass, Low Shelf, High Shelf
Output Delay0 ms to 50 ms per output
Presets5 preset scenes
Network and Control
Transmission Distance328 ft (100 m) over CAT6/6A/7
IP ModeDHCP (default) or Static, set separately for primary and secondary networks
ControlWeb GUI, Dante® Controller, TCP/IP (port 8000, default), Telnet (port 23, default); RelayAV
ESD ProtectionIEC 61000-4-2: +/-8 kV (air-gap discharge), +/-4 kV (contact discharge)
Connectors
Mic/Line Inputs12-pin 3.5mm Phoenix connectors, 8 channels
Line Outputs12-pin 3.5mm Phoenix connectors, 8 channels
Dante® Primary1x locking RJ45, PoE+ PD (IEEE 802.3at, Class 4); Dante®/AES67 audio, Web GUI, TCP/IP and RelayAV control
Dante® Secondary1x locking RJ45, PoE+ PD (IEEE 802.3at, Class 4); Dante®/AES67 audio, Web GUI, TCP/IP and RelayAV control
DC Power1x 2-pin 12V DC locking power jack, max 2.5A
Indicators and Controls
Front PanelPOWER LED, STATUS LED, RESET button
Rear Panel8x +48V phantom power indicators
Power
Power Supply12V/2.5A locking DC power supply, or PoE+ PD (IEEE 802.3at, Class 4)
Power Consumption13.68W (max)
Physical
HousingMetal enclosure
ColorBlack
Mounting19-inch rack-mount (mounting ears included)
Dimensions (W x D x H)11.81 x 7.09 x 1.73 in (300 x 180 x 44 mm)
Weight3.25 lbs (1.475 kg)
Shipping Dimensions14.45 x 9.37 x 3.74 in (367 x 238 x 95 mm)
Environmental
Operating Temperature32°F to 104°F (0°C to 40°C)
Storage Temperature-4°F to 140°F (-20°C to 60°C)
Operating Humidity20% to 80% RH, non-condensing
Storage Humidity10% to 90% RH, non-condensing
Package Contents
1x8x8 Line Audio Bridge with Dante® and PoE+
1x12V/2.5A locking power supply with optional multinational conversion plug
2xMounting ear
10xMachine screw
4x12-pin 3.5mm Phoenix connector (male)
Dante 8x8 Analog Audio Bridge with DSP, Phoenix I/O, PoE+ panel drawing
Dante 8x8 Analog Audio Bridge with DSP, Phoenix I/O, PoE+ system diagram
Dante 8x8 Analog Audio Bridge with DSP, Phoenix I/O, PoE+ applications
in the same range
AUD-DTE-2X2XLR 2x2 XLR Dante Audio Bridge with DSP, 8-Band PEQ and Delay
Mic-to-Line Analog onto Dante® and Back, Tuned at the Box, from -35dB...
B2B portal only
in the same range
AUD-DTE-16X16XLR 16x16 XLR Audio Bridge with Dante® and PoE+, 19" Rack Mount
One Chassis Replaces Separate Input and Output Units - 16 XLR/TRS Com...
B2B portal only
in the same range
AUD-DTE-8X8XLR 8x8 XLR to Dante/AES67 Audio Bridge with +48V Phantom, PEQ an...
Mic and Line Sources onto a Dante® Network Without a Separate Preamp ...
B2B portal only
in the same range
AUD-DTE-4X4LINE 4x4 Mic/Line Dante® and AES67 Bridge with 8-Band PEQ and Delay
Tune and Time-Align at the Interface - 8-Band PEQ on All 8 I/O, Up to...
B2B portal only
in the same range
AUD-DTE-4X4XLR 4x4 XLR Dante® Audio Bridge, Mic/Line Inputs with +48V, 8-Ban...
Level-Match, EQ and Time-Align at the Bridge - 8-Band PEQ on Every In...
B2B portal only

Buying for resale, a project, or your own site?

Trade accounts see net pricing, stock and one-click reorder from past jobs. Dealers, integrators, businesses, schools and public bodies all qualify. Approval is usually the same working day.